 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ASAHI KASEI [AK6416A] AK6416A 16Kbit Serial CMOS EEPROM Features ADVANCED CMOS EEPROM TECHNOLOGY READ/WRITE NON-VOLATILE MEMORY - Wide Vcc (1.8V 5.5V) operation - 16384 bits: 1024 O 16 organization ONE CHIP MICROCOMPUTER INTERFACE - Interface with one chip microcomputer's serial communication port directly LOW POWER CONSUMPTION - 0.8A Max (Standby mode) HIGH RELIABILITY -Endurance : 100K cycles -Data Retention : 10 years SPECIAL FEATURES - High speed operation ( fMAX=4MHz: Vcc=4.5V 5.5V ) - Automatic write cycle time-out with auto-ERASE - Automatic address increment (READ) - Ready/Busy status signal - Software and Hardware controlled write protection IDEAL FOR LOW DENSITY DATA STORAGE - Low cost, space saving, 8-pin package (SSOP) Block diagram DAS02E-00 -11999/05 ASAHI KASEI [AK6416A] General Description The AK6416A is a 16384bit, serial, read/write, non-volatile memory device fabricated using an advanced CMOS EEPROM technology. The AK6416A has 16384bits of memory organized into 1024 registers of 16 bits each. The AK6416A can operate full function under wide operating voltage range from 1.8V to 5.5V. The charge up circuit is integrated for high voltage generation that is used for write operation. The AK6416A can connect to the serial communication port of popular one chip microcomputer directly (3 line negative clock synchronous interface). At write operation, AK6416A takes in the write data from data input pin (DI) to a register synchronously with rising edge of input pulse of serial clock pin (SK). And at read operation, AK6416A takes out the read data from a register to data output pin (DO) synchronously with falling edge of SK. The AK6416A has 4 instructions such as READ, WRITE, WREN (write enable) and WRDS (write disable). Each instruction is organized by op-code block (8bits), address block (8bits) and data (8bits O 2). When input level of SK pin is high level and input level of chip select (CS) pin is changed from high level to low level, AK6416A can receive the instructions. Special features of the AK6416A include : automatic write time-out with auto-ERASE, Ready/Busy status signal output and ultra-low standby power mode when deselected (CS=high). * Software and Hardware controlled write protection The AK6416A has 2 (hardware and software) write protection functions. After power on or after execution of WRDS (write disable) instruction, execution of WRITE instruction will be disabled. This write protection condition continues until WREN instruction is executed or Vcc is removed from the part. Execution of READ instruction is independent of both WREN and WRDS instructions. Reset pin should be low level when WRITE instruction is executed. When the Reset pin is high level, the WRITE instruction is not executed. * Ready/Busy status signal During the automatic write time-out period (BUSY status), the AK6416A can't accept the other instructions. The AK6416A has 2 functions to know the Busy status from exterior. The RDY/BUSY pin indicates the Busy status regardless of the CS pin status. The RDY/BUSY pin outputs the low level regardless of the CS pin status during Busy status. Except the above status, this pin outputs high level. Also the DO pin indicates the Busy status. When input level of SK pin is low level and input level of CS pin is changed from high level to low level, the AK6416A is in the status output mode and the DO pin indicates the Ready/Busy status. The Ready/Busy status outputs on DO pin until CS pin is changed from low level to high level, or first bit ("1") of op-code of next instruction is given to the part. Except when the device is in the status output mode or outputs data, the DO pin is in the high impedance state. Type of Products Model AK6416AM Memory size 16Kbits Temp.Range -40C85C Vcc 1.8V5.5V Package 8pin Plastic SSOP DAS02E-00 -2- 1999/05 ASAHI KASEI [AK6416A] Pin arrangement Pin Function Pin No. 1 2 3 4 5 6 7 8 Pin name CS SK DI DO GND RESET RDY/BUSY Vcc I O I/O I I I O Note I : Input pin O : Output pin DAS02E-00 -3- 1999/05 ASAHI KASEI Pin Description [AK6416A] CS (Chip Select) When SK is high level and CS is changed from high level to low level, AK6416A can receive the instructions. CS should be kept low level while receiving op-code, address and data and while outputting data. If CS is changed to high level during the above period, AK6416A stops the instruction execution. When SK is low and CS is changed from high level to low level, AK6416A will be in status output mode. The CS need not be low level during the automatic write time-out period (BUSY status). SK (Serial Clock) The SK clock pin is the synchronous clock input for input/output data. At write operation, AK6416A takes in the write data from data input pin (DI) synchronously with rising edge of input pulse of serial clock pin (SK). And at read operation, AK6416A takes out the read data to data output pin (DO) synchronously with falling edge of SK. The SK clock is not needed during the automatic write time-out period (BUSY status), the status output period and when the device isn't selected (CS = high level). DI (Data Input) The op-code, address and write data is input to the DI pin. DO (Data Output) The DO pin outputs the read data and status signal and will be high impedance except for this timing. RDY/BUSY (Ready/Busy status) This pin outputs the internal programming status. When the AK6416A is in the automatic write time-out period, this pin outputs the low level (BUSY status), and outputs the high level except for this timing. RESET (Reset) The AK6416A stops executing the write instruction when the RESET pin is high level. The RESET pin should be low level while the write instruction input period and the automatic write time-out period. If the RESET pin is high level while the automatic write time-out period, the AK6416A stops execution of internal programming and the device returns to ready status. In this case the word data of the specified address will be incomplete. When inputting the new instruction after RESET, the CS pin should be set to high level. The read, write enable and write disable instructions are not affected by RESET pin status. Vcc (Power Supply) GND (Ground) DAS02E-00 -4- 1999/05 ASAHI KASEI [AK6416A] Functional Description The AK6416A has 4 instructions such as READ, WRITE, WREN (write enable) and WRDS (write disable). Each instruction is organized by op-code block (8bits), address block (8bits) and data (8bits O 2). When input level of SK pin is high level and input level of chip select (CS) pin is changed from high level to low level, AK6416A can receive the instructions. When the instructions are executed consecutively, the CS pin should be brought to high level for a minimum of 250ns(Tcs) between consecutive instruction cycle. Instruction Set For 6416A Instruction WRITE READ WREN WRDS ( WRAL ) Op-Code 1 0 1 0 0 1 A9 A8 1 0 1 0 1 0 A9 A8 10100011 10100000 10101111 Address A7 A6 A5 A4 A3 A2 A1 A0 A7 A6 A5 A4 A3 A2 A1 A0 OyyyOyyyOyyyOyyyOyyyOyyyOyyyO OyyyOyyyOyyyOyyyOyyyOyyyOyyyO OyyyOyyyOyyyOyyyOyyyOyyyOyyyO Data D15 -D0 D15 -D0 D15 -D0 O:don't care (Note) The WRAL instruction is used for factory function test only. User can't use this instruction . Write The write instruction is followed by 16 bits of data to be written into the specified address. After the 32nd rising edge of SK to read D0 in, the AK6416A will be put into the automatic write time-out period. During the automatic write time-out period (Busy status)and while entering write instruction, the RESET pin should be low level. If the RESET pin is set to high level during the automatic write time-out period, the AK6416A stops execution of internal programming and the device returns to ready status. In this case the word data of the specified address will be incomplete. When inputting the new instructoin after RESET, the CS pin should be set to high level. When inputting the new instruction after RESET, the CS pin should be set to high level. When the RESET pin is kept at high level, the write is not executed. This becomes write protection function. The CS pin need not be high level during automatic write time-out period (BUSY status). WRITE DAS02E-00 -5- 1999/05 ASAHI KASEI [AK6416A] Read The read instruction is the only instruction which outputs serial data on the DO pin. When the 17th falling edge of SK is received , the DO pin will come out of high impedance state and shift out the data from D15 first in descending order which is located at the address specified in the instruction. The data in the next address can be read sequentially by continuing to provide clock. The address automatically cycles to the next higher address after the 16bit data shifted out. When the highest address is reached ($3FF), the address counter rolls over to address $000 allowing the read cycle to be continued indefinitely. READ WREN / WRDS ( Write Enable and Write Disable ) When Vcc is applied to the part, it powers up in the programming disable (WRDS) state. Programming must be preceded by a programming enable (WREN) instruction. Programming remains enabled until a programming disable (WRDS) instruction is executed or Vcc is removed from the part. The programming disable instruction is provided to protect against accidental data disturb. Execution of a read instruction is not affected by both WREN and WRDS instructions. WREN/WRDS DAS02E-00 -6- 1999/05 ASAHI KASEI [AK6416A] Absolute Maximum Ratings Parameter Power Supply All Input Voltages with Respect to Ground Ambient storage temperature Symbol VCC VIO Tst Min -0.6 -0.6 -65 Max +7.0 VCC+0.6 +150 Unit V V C Stress above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specification is not implied. Exposure to absolute maximum conditions for extended periods may affect device reliability. Recommended Operating Condition Parameter Power Supply Ambient Operating Temperature Symbol VCC Ta Min 1.8 -40 Max 5.5 +85 Unit V C DAS02E-00 -7- 1999/05 ASAHI KASEI [AK6416A] Electrical Characteristics (1) D.C. ELECTRICAL CHARACTERISTICS ( 1.8VVcc5.5V, -40CTa85C, unless otherwise specified ) Parameter Current Dissipation (WRITE) Current Dissipation (READ,WREN, WRDS) Current Dissipation (Standby) Input High Voltage1 CS, SK, RESET pin Input High Voltage2 DI pin Input Low Voltage1 CS, SK, RESET pin Input Low Voltage2 DI pin Output High Voltage Symbol ICC1 ICC2 ICC3 ICC4 ICC5 ICC6 ICCSB VIH1 VIH2 VIH3 VIL1 VIL2 VIL3 VOH1 VOH2 Condition VCC=5.5V, tSKP=250ns, *1 VCC=2.5V, tSKP=500ns, *1 VCC=1.8V, tSKP=1.0us, * 1 VCC=5.5V, tSKP=250ns, *1 VCC=2.5V, tSKP=500ns, *1 VCC=1.8V, tSKP=1.0us, *1 VCC=5.5V 1.8VVCC5.5V 2.5VVCC5.5V 1.8VVCC<2.5V 1.8VVCC5.5V 2.5VVCC5.5V 1.8VVCC<2.5V 2.5VVCC5.5V IOH=-50A 1.8VVCC<2.5V IOH=-50A 2.5VVCC5.5V IOL=1.0mA 1.8VVCC<2.5V IOL=0.1mA VCC=5.5V,VIN=5.5V VCC=5.5V VOUT=5.5V,CS=VCC *2 Min. Max. 5.5 3.5 2.5 1.5 0.3 0.2 0.8 Unit mA mA mA mA mA mA uA V V V V V V V V 0.8 OVCC 0.7 O VCC 0.8 O VCC 0 0 0 VCC-0.3 VCC-0.3 VCC+0.5 VCC+0.5 VCC+0.5 0.2 O VCC 0.3 O VCC 0.2 O VCC Output Low Voltage VOL1 VOL2 0.4 0.4 `1.0 `1.0 V V Input Leakage Output Leakage ILI ILO uA uA *1: VIN=VIH/VIL, DO=RDY/BUSY=Open *2: CS=Vcc, SK/DI/RESET=Vcc/GND,DO=RDY/BUSY=Open DAS02E-00 -8- 1999/05 ASAHI KASEI (2) A.C. ELECTRICAL CHARACTERISTICS [AK6416A] ( 1.8VVcc5.5V, -40CTa85C, unless otherwise specified ) Parameter SK Cycle Time Symbol tSKP1 tSKP2 tSKP3 Condition 4.5VVCC5.5V 2.5VVCC<4.5V 1.8VVCC<2.5V 4.5VVCC5.5V 2.5VVCC<4.5V 1.8VVCC<2.5V 4.5VVCC5.5V 1.8VVCC<4.5V 4.5VVCC5.5V 1.8VVCC<4.5V Min. 250 500 1.0 125 250 500 50 100 50 100 50 100 0 0 Max. Unit ns ns us ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SK Pulse Width tSKW1 tSKW2 tSKW2 CS Setup Time tCSS1 tCSS2 CS Hold Time tCSH1 tCSH2 SK Setup Time tSKSH/L1 4.5VVCC5.5V tSKSH/L2 1.8VVCC<4.5V RESET Setup Time RESET Hold Time Data Setup Time tRESS tRESH tDIS1 tDIS2 tDIS3 4.5VVCC5.5V 2.5VVCC<4.5V 1.8VVCC<2.5V 4.5VVCC5.5V 2.5VVCC<4.5V 1.8VVCC<2.5V 4.5VVCC5.5V, *3 2.5VVCC<4.5V, *3 1.8VVCC<2.5V, *3 CL=100pF 2.5VVCC5.5V 1.8VVCC<2.5V 50 100 200 50 100 200 75 150 300 1 7 10 100 250 500 Data Hold Time tDIH1 tDIH2 tDIH3 DO pin Output delay RDY/BUSY pin Output delay Selftimed Programming Time Write Recovery Time Min CS High Time DO High-Z Time *3:CL=100pF tPD1 tPD2 tPD3 tPD tE/W1 tE/W2 tRC tCS tOZ ns ns ns us ms ms ns ns ns DAS02E-00 -9- 1999/05 ASAHI KASEI [AK6416A] Synchronous Data Timing Instruction Input Data Output (READ) DAS02E-00 - 10 - 1999/05 ASAHI KASEI [AK6416A] Data Output (READ) Ready / BUSY Signal Output(RDY/BUSY pin) DAS02E-00 - 11 - 1999/05 ASAHI KASEI [AK6416A] Ready / BUSY Signal Output (DO pin) DAS02E-00 - 12 - 1999/05 |
Price & Availability of AK6416A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |